Welcome to the Gundam Forums.

Search:

Type: Posts; User: Mark

Page 1 of 12 1 2 3 4

Search: Search took 0.01 seconds.

  1. Thread: Marks WIPs

    by Mark
    Replies
    72
    Views
    4,139

    Re: Marks WIPs

    Car duties complete and a happy quiet car, only one injury. Back onto the Red Saber and the Gatling set.
  2. Replies
    10
    Views
    313

    Re: 1:35 Snake Eyes S.A.F.S (Ma.K)

    Nice work there Squee. Love the chipping.
  3. Thread: Marks WIPs

    by Mark
    Replies
    72
    Views
    4,139

    Re: Marks WIPs

    I have slowed on the building for now. I have a Mazdaspeed 6 to do a VVT actuator change and well a replacement of all the timing and oil pump chains and associated bits. Spent the last few days...
  4. Thread: Marks WIPs

    by Mark
    Replies
    72
    Views
    4,139

    Re: Marks WIPs

    Thats better. A pic in daylight. The other pics were taken under a fluro light from my desk magnifier and the colour is never as it appears and it always hides the panel lining.

    The stickers...
  5. Thread: Squee's WB

    by Mark
    Replies
    3,091
    Views
    246,859

    Re: Squee's WB

    Sweeeeeet. So much sanding. lol
  6. Thread: Marks WIPs

    by Mark
    Replies
    72
    Views
    4,139

    Re: Marks WIPs

    A bit of progress on the red saber. Pic isn't brilliant but I've chosen to make the red less like tomato soup red and more like red red with clear blue shading to darken the red in places. Just...
  7. Replies
    72
    Views
    3,826

    Re: Vile's Project Room

    Cool, hopefully it will behave for ya now. Lacquer thinner should work with the Mr Surfacer.
  8. Replies
    72
    Views
    3,826

    Re: Vile's Project Room

    I'd suggest it's definitely the valve leaking, there should be no air coming out of the assembly as you have it in the last 3 pics? Air should only flow if you depress the brass pin. Can you pull...
  9. Replies
    72
    Views
    3,826

    Re: Vile's Project Room

    ahhh, you need to pull the valve where the hose connects and apply a small amount of Vaseline to the pin in the airbrush that drives the valve, it has dried out and got stuck on the small o ring. I...
  10. Replies
    72
    Views
    3,826

    Re: Vile's Project Room

    Oh meant to mention.... Bees wax rolled really thin and then wrapped on the stop of the threads and then once it's all assembled heat the tip is a great way of sealing any small air leaks. The fiber...
  11. Thread: Scorn's Workshop

    by Mark
    Replies
    246
    Views
    23,680

    Re: Scorn's Workshop

    I use a Makerbot II at work for prototyping work stuff and the occasional "alignment print". I really must get my own. I work with Creo Parametric for Mechanical design.

    Mark
  12. Replies
    597
    Views
    56,175

    Re: RPC's WIP ~ my first MG's

    Well, you are doing a fantastic job RPC. Wishes I had half the brush skills you have mate.
  13. Replies
    72
    Views
    3,826

    Re: Vile's Project Room

    Hey, sorry to hear of your problems, Hang in there.

    With the Air Brush, get a cheap ebay .2 to .5 and polish the needles. You can get them dirt cheap and so long as you polish up the needles with...
  14. Thread: Marks WIPs

    by Mark
    Replies
    72
    Views
    4,139

    Re: Marks WIPs

    Squee, from memory with the great saber, yes there was an issue with that middle section as you discovered. I'll see if it's the same with the red saber as well. I just finished the neck and chest...
  15. Thread: Scorn's Workshop

    by Mark
    Replies
    246
    Views
    23,680

    Re: Scorn's Workshop

    Ohhh I tried the Acetone Vapour bath bit on a Printed bust for a RC WW2 Pilot Bust (90mm across the shoulders). Worked awesomely. Anyone 3D printing ABS should give it a try.....

    Nice work Scorn.
  16. Thread: Marks WIPs

    by Mark
    Replies
    72
    Views
    4,139

    Re: Marks WIPs

    Thanks Quik Brik.

    My Lightning Saix has arrived at my friends house so I'll pick that up tomorrow so I can start the Zoids Torture all over again. lol Kinda sucks as I have the day off work today...
  17. Thread: Squee's WB

    by Mark
    Replies
    3,091
    Views
    246,859

    Re: Squee's WB

    My cat steals prepared parts and hides them... js

    The kitty is kinda cool
  18. Replies
    597
    Views
    56,175

    Re: RPC's WIP ~ my first MG's

    I have never had much luck with flesh colours, but so far that's lookin pretty good RPC
  19. Replies
    5,823
    Views
    548,916

    Sticky: Re: Latest Kit Acquisitions!

    The heavy arms is cool... say no more..... lol

    - - - Updated - - -

    Oh well folded to the external pressure (ok to my own pressure) and got the Kotobukia Zoids beam Gatling set for 28USD...
  20. Replies
    5,823
    Views
    548,916

    Sticky: Re: Latest Kit Acquisitions!

    Interestingly enough the Red Saber is going together better than the Great Saber peg wise. Samuel has had a printer issue apparently so I'll have to wait a bit for the waterslides, but he can do...
  21. Replies
    10
    Views
    440

    Re: Some current WIP's

    yeah really nice work on the Kashatria. I really like the Cybaster as well, been looking at getting one.
  22. Replies
    5,823
    Views
    548,916

    Sticky: Re: Latest Kit Acquisitions!

    One arrived, second in transit.

    http://www.gundamforums.com/attachment.php?attachmentid=21297

    Contents is good, nice crisp parts, but the silver parts.... they are like Bandai gold bits......
  23. Replies
    597
    Views
    56,175

    Re: RPC's WIP ~ my first MG's

    It is a bargain, the Warhammer 40,000 stuff here is really pricey. The quality looks really good
  24. Replies
    597
    Views
    56,175

    Re: RPC's WIP ~ my first MG's

    awesome, I know the prices go up on subsequent releases usually but even if they do it should still be a good price. Good score RPC
  25. Replies
    597
    Views
    56,175

    Re: RPC's WIP ~ my first MG's

    ohhh cool is that a new release meaning you can get more or was it an old release you happened to find?
Results 1 to 25 of 300
Page 1 of 12 1 2 3 4