Welcome to the Gundam Forums.
Tab Content
  • Mark's Avatar
    October 9, 2018, 4:30 PM
    Mark replied to a thread Marks WIPs in Works-In-Progress
    Car duties complete and a happy quiet car, only one injury. Back onto the Red Saber and the Gatling set.
    72 replies | 4159 view(s)
  • Mark's Avatar
    October 9, 2018, 4:27 PM
    Nice work there Squee. Love the chipping.
    10 replies | 343 view(s)
  • Mark's Avatar
    October 3, 2018, 10:32 AM
    Mark replied to a thread Marks WIPs in Works-In-Progress
    I have slowed on the building for now. I have a Mazdaspeed 6 to do a VVT actuator change and well a replacement of all the timing and oil pump...
    72 replies | 4159 view(s)
  • Mark's Avatar
    September 21, 2018, 1:42 AM
    Mark replied to a thread Marks WIPs in Works-In-Progress
    Thats better. A pic in daylight. The other pics were taken under a fluro light from my desk magnifier and the colour is never as it appears and it...
    72 replies | 4159 view(s)
  • Mark's Avatar
    September 21, 2018, 1:36 AM
    Mark replied to a thread Squee's WB in Works-In-Progress
    Sweeeeeet. So much sanding. lol
    3091 replies | 247107 view(s)
  • Mark's Avatar
    September 18, 2018, 8:59 PM
    Mark replied to a thread Vile's Project Room in Works-In-Progress
    Cool, hopefully it will behave for ya now. Lacquer thinner should work with the Mr Surfacer.
    72 replies | 3847 view(s)
  • Mark's Avatar
    September 18, 2018, 8:01 PM
    Mark replied to a thread Vile's Project Room in Works-In-Progress
    I'd suggest it's definitely the valve leaking, there should be no air coming out of the assembly as you have it in the last 3 pics? Air should only...
    72 replies | 3847 view(s)
  • Mark's Avatar
    September 18, 2018, 7:42 PM
    Mark replied to a thread Vile's Project Room in Works-In-Progress
    ahhh, you need to pull the valve where the hose connects and apply a small amount of Vaseline to the pin in the airbrush that drives the valve, it...
    72 replies | 3847 view(s)
  • Mark's Avatar
    September 18, 2018, 4:59 PM
    Mark replied to a thread Vile's Project Room in Works-In-Progress
    Oh meant to mention.... Bees wax rolled really thin and then wrapped on the stop of the threads and then once it's all assembled heat the tip is a...
    72 replies | 3847 view(s)
  • Mark's Avatar
    September 18, 2018, 4:55 PM
    Mark replied to a thread Scorn's Workshop in Works-In-Progress
    I use a Makerbot II at work for prototyping work stuff and the occasional "alignment print". I really must get my own. I work with Creo Parametric...
    246 replies | 23716 view(s)
  • Mark's Avatar
    September 18, 2018, 7:11 AM
    Well, you are doing a fantastic job RPC. Wishes I had half the brush skills you have mate.
    597 replies | 56296 view(s)
  • Mark's Avatar
    September 18, 2018, 3:23 AM
    Mark replied to a thread Vile's Project Room in Works-In-Progress
    Hey, sorry to hear of your problems, Hang in there. With the Air Brush, get a cheap ebay .2 to .5 and polish the needles. You can get them dirt...
    72 replies | 3847 view(s)
  • Mark's Avatar
    September 18, 2018, 3:13 AM
    Mark replied to a thread Marks WIPs in Works-In-Progress
    A bit of progress on the red saber. Pic isn't brilliant but I've chosen to make the red less like tomato soup red and more like red red with clear...
    72 replies | 4159 view(s)
No More Results
About Mark

Basic Information

About Mark
Location:
Adelaide, Australia

Statistics


Total Posts
Total Posts
304
Posts Per Day
0.39
General Information
Last Activity
Today 8:15 AM
Join Date
September 1, 2016
Referrals
0

1 Friend

  1. lgt1977 lgt1977 is offline

    Senior Member

    • Send a message via Skype™ to lgt1977
    lgt1977
Showing Friends 1 to 1 of 1